Finden Sie schnell fräser für gewinde für Ihr Unternehmen: 15 Ergebnisse

kelteks Needled Combimat is the combination of woven roving bonded by needling to a mat without chemical binding. This needling method adds volume to fibers thus adding thickness to parts. This product range is particularly recommended for the manufacture with pultrusion process for parts that require great mechanical properties. kelteks Combimat Needled is highly drapable and suitable for laminating corners and edges. Country of origin: Croatia Industry: Composites Weight: 300g+300g Width: 20-350cm Length: 40-200cm

kelteks Needled Combimat is the combination of woven roving bonded by needling to a mat without chemical binding. This needling method adds volume to fibers thus adding thickness to parts. This product range is particularly recommended for the manufacture with pultrusion process for parts that require great mechanical properties. kelteks Combimat Needled is highly drapable and suitable for laminating corners and edges. Country of origin: Croatia Industry: Composites Weight: 240g+200g Width: 20-350cm Length: 40-200cm

Multi-layer composite reinforcement We are proud of the fact that we are one of the few companies that use the needling process, and probably the only one that connects layers with needling, gluing or stitching advanced technology. - Excellent Formability - Even resin flow - Greater volume SAVES TIME kelteks FormMat consists of 2 layers of chopped fibers and 1 layer of a veil which saves you the time of work and preparation. Does not wear out during processing which gives a better surface aspect than most of other reinforcements. SUPER VOLUME kelteks FormMat is a premium fabric for sharp-edged parts because high-volume fibers allow optimal coverage of critical areas. MECHANICALLY BONDED kelteks FormMat is mechanically bonded by the needle-loom process, without chemical binding adds volume to reinforcements which means greater part thicknesses can be achieved. MECHANICAL PROPERTIES kelteks FormMat is especially suitable for the manufacture of parts that require mechanical properties such as Construction /building, Wind industry, Automotive /transportation, Marine, Sport & Leisure, Medical equipment, etc. Country of origin: Croatia Industry: Composites Weight: 600/250/600

Multi-layer composite reinforcement We are proud of the fact that we are one of the few companies that use the needling process, and probably the only one that connects layers with needling, gluing or stitching advanced technology. - Excellent Formability - Even resin flow - Greater volume SAVES TIME kelteks FormMat consists of 2 layers of chopped fibers and 1 layer of a veil which saves you the time of work and preparation. Does not wear out during processing which gives a better surface aspect than most of other reinforcements. SUPER VOLUME kelteks FormMat is a premium fabric for sharp-edged parts because high-volume fibers allow optimal coverage of critical areas. MECHANICALLY BONDED kelteks FormMat is mechanically bonded by the needle-loom process, without chemical binding adds volume to reinforcements which means greater part thicknesses can be achieved. MECHANICAL PROPERTIES kelteks FormMat is especially suitable for the manufacture of parts that require mechanical properties such as Construction /building, Wind industry, Automotive /transportation, Marine, Sport & Leisure, Medical equipment, etc. Country of origin: Croatia Industry: Composites Weight: 450/250/450

Multi-layer composite reinforcement We are proud of the fact that we are one of the few companies that use the needling process, and probably the only one that connects layers with needling, gluing or stitching advanced technology. - Excellent Formability - Even resin flow - Greater volume SAVES TIME kelteks FormMat consists of 2 layers of chopped fibers and 1 layer of a veil which saves you the time of work and preparation. Does not wear out during processing which gives a better surface aspect than most of other reinforcements. SUPER VOLUME kelteks FormMat is a premium fabric for sharp-edged parts because high-volume fibers allow optimal coverage of critical areas. MECHANICALLY BONDED kelteks FormMat is mechanically bonded by the needle-loom process, without chemical binding adds volume to reinforcements which means greater part thicknesses can be achieved. MECHANICAL PROPERTIES kelteks FormMat is especially suitable for the manufacture of parts that require mechanical properties such as Construction /building, Wind industry, Automotive /transportation, Marine, Sport & Leisure, Medical equipment, etc. Country of origin: Croatia Industry: Composites Weight: 300/180/300

Multi-layer composite reinforcement We are proud of the fact that we are one of the few companies that use the needling process, and probably the only one that connects layers with needling, gluing or stitching advanced technology. - Excellent Formability - Even resin flow - Greater volume SAVES TIME kelteks FormMat consists of 2 layers of chopped fibers and 1 layer of a veil which saves you the time of work and preparation. Does not wear out during processing which gives a better surface aspect than most of other reinforcements. SUPER VOLUME kelteks FormMat is a premium fabric for sharp-edged parts because high-volume fibers allow optimal coverage of critical areas. MECHANICALLY BONDED kelteks FormMat is mechanically bonded by the needle-loom process, without chemical binding adds volume to reinforcements which means greater part thicknesses can be achieved. MECHANICAL PROPERTIES kelteks FormMat is especially suitable for the manufacture of parts that require mechanical properties such as Construction /building, Wind industry, Automotive /transportation, Marine, Sport & Leisure, Medical equipment, etc. Country of origin: Croatia Industry: Composites Weight: 450/180/450

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 200 soft material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 50 material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 200 material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 75 soft material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector C500 material: Carbon fiber length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 50 soft material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 100 material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 75 material: Fiberglass length: 50m

NEW solution for the perfect corner reinforcement. kelteks EDGE PROTECTOR is the NEW solution for the perfect corner reinforcement. Fluffy and cuddly fibers are easily squeezed into sharp-edged joints and corners so stress-cracking and laminate chipping is effectively prevented. What is the problem? - There is always the problem that not enough glass fibers go into the sharp corners or edges with a small radius. - Glass fiber mat usually would not stretch into the corner resulting in a “resin-nest” (too much resin) which is not reinforced with fibers. Sometimes air bubbles get trapped in there. These little voids are defects and weak spots, weakening the structural strength of your composite. After un-moulding this unreinforced corner is very sensitive to break, because there are no fibers inside (resin excess). The result is “stress cracking” and that almost always happen in radiuses of corners and edges. - Products that are on the market are very hard and stiff and will not be squeezed into the corner, unless they are really precisely placed. That’s how kelteks EDGE PROTECTOR works: - The structure of the kelteks EDGE PROTECTOR is fluffy and cuddly and is available in different thicknesses. It can be easily moulded and, as an insert in the preform, it adapts well to any contour. - Fluffy and cuddly fibers are easily squeezed into the sharp-edged joints and corners. - Sharp-edged joints and corners in critical component areas are thus reliably filled with fibers and laminate chipping is effectively prevented. - kelteks EDGE PROTECTOR is suitable for all processes of composites making, such as hand lamination, vacuum infusion, pultrusion, etc. - The transversely aligned entanglement fibers ensure a perfect bond to the overlying laminate layers. country of origin: Croatia type: Corner reinforcement industry: Composites variations: kelteks Edge Protector 100 soft material: Fiberglass length: 50m